AI-generated imageGuides · Strength training · Updated 2026-10-30
What is Starting Strength, and how does the program work?
Starting Strength is a beginner barbell program by strength coach Mark Rippetoe. You train 3 days a week, alternating two full-body workouts. Every session starts with 3 sets of 5 squats, then a press and a pull from the floor. You add a little weight every workout until a lift stops moving, which for most beginners takes a few months.
- Workout A. Squat 3 sets of 5. Overhead press 3 sets of 5. Deadlift 1 set of 5.
- Workout B. Squat 3 sets of 5. Bench press 3 sets of 5. Deadlift 1 set of 5, later swapped for power cleans, 5 sets of 3.
- Alternate. Train 3 days a week on days that aren't back to back, such as Monday, Wednesday and Friday. Week one is A, B, A. Week two is B, A, B.
- Add weight. Add weight to every lift each session while you still get all your reps with good form.
The two workouts
Starting Strength has two workouts. You do them in turn, three days a week, with a rest day between sessions.
| Workout A | Workout B | |
|---|---|---|
| First | Squat, 3 sets of 5 | Squat, 3 sets of 5 |
| Second | Overhead press, 3 sets of 5 | Bench press, 3 sets of 5 |
| Third | Deadlift, 1 set of 5 | Deadlift, 1 set of 5 |
“3 sets of 5” means three sets at the same weight, not counting warm-ups. The deadlift gets only one work set, because it’s hard to recover from and you’re already squatting every session. Rest 3 to 5 minutes between heavy sets so you can get all your reps.
On a Monday, Wednesday and Friday schedule, week one is A, B, A and week two is B, A, B.
The program grows in phases
You don’t change programs as you get stronger. You change a few pieces and keep your weights.
| Phase | What changes | How long |
|---|---|---|
| 1 | The two workouts above | Usually 2 to 3 weeks |
| 2 | Power cleans, 5 sets of 3, take the deadlift’s place in Workout B | A few months for most people |
| 3 | The middle squat of the week gets lighter, about 80% of Monday’s weight. Chin-ups join the pulls in turn. | Until the lifts stop moving |
Move to Phase 2 when the deadlift gets heavy enough that you still feel the last one at your next session.
Adding weight
Add weight to every lift every session while you still get all your reps.
- Young men, early on: about 10 lb (5 kg) on the squat for the first 2 or 3 sessions, 15 to 20 lb on the deadlift for the first couple, then 10 lb for several more. After that, 5 lb (2.5 kg) jumps.
- Press, bench press and power clean: maybe one 10 lb jump, then 5 lb.
Women and lifters over about 35 to 40 often need smaller jumps from the start, such as one 10 lb jump on the squat and 5 lb on the presses, and 2.5 lb jumps sooner.
Small plates help a lot once the presses slow down. Our Starting Strength planner writes out every workout with its weight.
Picking your starting weights
Start each lift with the empty bar for a set of 5. Add weight in small jumps, one set of 5 at a time. Stop when the bar starts to slow down. Don’t go to failure. That weight is your first work set. It will feel light, and that’s the point: you’ll add weight every session from there.
If you already know roughly what you can lift, the beginner weight guide covers starting points for each exercise.
When a lift stalls
Missing a rep once is normal. Repeat the weight next time. If you keep missing:
- Check the basics first: more sleep and more food fix most early stalls.
- Use smaller jumps: 2.5 lb or less, especially on the presses.
If it still stalls, reset: take 5 to 10% off that lift only and work back up. It usually goes past the old weight.
When resets stop working, you’ve used up what a beginner program can give you, and it’s time for one that adds weight weekly. That’s a good problem to have. The idea behind all of it is progressive overload.
Also asked
What weight should I start Starting Strength with?
Start with the empty bar for a set of 5, then add weight in small jumps, a set of 5 at a time. Stop when the bar starts to slow down, well before it gets hard. That weight is your first 3 sets of 5. It should feel easy, because you'll add weight every session from there.
How much weight do I add each workout?
Most young men can add 10 lb (5 kg) to the squat for the first 2 or 3 sessions and 15 to 20 lb to the deadlift for the first couple, then settle into 5 lb (2.5 kg) jumps. Women and lifters over about 35 to 40 start with smaller jumps, and the presses usually go up 5 lb at a time from day one, then 2.5 lb or less.
What do I do when I stall?
First repeat the weight and use smaller jumps. Check that you're sleeping and eating enough. If a lift still won't move, take 5 to 10% off that lift and build back up. When resets stop working, it's time for a program that adds weight weekly instead of every session.
How long should I run Starting Strength?
As long as you can keep adding weight each session. The first phase usually lasts 2 to 3 weeks, and most people spend a few months in the next one before the upper-body lifts slow down. A third phase with a light squat day stretches it further.
Starting Strength or StrongLifts 5x5?
Both are 3-day beginner programs built on the squat and add weight every session. Starting Strength uses 3 sets of 5 and adds power cleans later. StrongLifts uses 5 sets of 5 and adds barbell rows. Both work well for a new lifter, so pick the one you'll stick with.
Is Starting Strength good for beginners?
Yes, it was written for them. It uses only a few lifts and adds weight as fast as a beginner can recover. If you're new, learn each lift with the empty bar first.